cell-phone

Clip-on gasket 6500

Clip-on EMI/RFI shielding gaskets with water seal. These gaskets are also know as trim gaskets or trim shield gaskets.

This easily mounted clip-on gasket is composed of two layers: a sponge rubber water seal, and an EMI-shielding side of highly conductive, wear-resistant metallized fabric. The gasket is very flexible due to the hollow rubber, ensuring a low closure force. The gasket is assembled without tools, simply by manually pressing the section onto the metal flange of your enclosure. Different sizes are available on request. The gasket can be bent in either direction (it can not be bent into a right angle, but it can form a rounded corner with a very small radius). Temperature ranges from -40 to +110 °C. A flame retardant version (UL94 V0) is also available.

Shielding performance
Shielding effectiveness depends on surface, shape of gasket and materials used.

Please note : These values are measured under laboratory conditions. Results may vary in other situations; please read our Guarantee.

Temperature resistance
An EPDM core with an operating temperature up to 100 °C and good resistance to UV, water, and acids make the clip-on shielding gaskets the right choice for outdoor applications.

Applications
Special shapes and materials excel in dynamic or high cycling applications such as Faraday cage doors or access panels with low compression rates and very limited compression set.

Available versions
The clip-on range comes in three flavors:

  • Type W series (Clip-on shielding gasket with water seal)
  • Type F series (Fully wrapped EMI/RFI-shielding gasket)
  • Type H series (For heavy-duty applications,for example military)

6500_types

Type W series
(Clip-on shielding gasket with water seal)

 example-type-W

The type W clip-on gasket series has been specially designed to provide environmental (water) sealing as well as EMI shielding for outdoor electronics and telecom cabinet manufacturers. The conductive textile is wrapped around one half of the gasket, dividing it into two parts: one part for electrical conductance and EMI shielding (made of highly conductive textile), and the other part for water sealing. The half-wrapped conductive textile provides over 96dB of broadband noise attenuation which is crucial for mid- to high-range shielding applications.

Type F series
(Fully wrapped EMI/RFI-shielding gasket)

 6500-example-type-F

The type-F clip-on gasket series has been specially designed to provide both EMI shielding and electrical conductivity. The conductive textile is wrapped around the entire gasket, resulting in higher shielding performance than type W (half wrapped version) - only at the expense of water resistance.

Type H series
(For heavy-duty applications,for example military)

 example-type-H

The type H clip-on gasket series has been specially designed for heavy-duty applications; in addition to EMI shielding it also provides low-frequency magnetic shielding. The type H series is covered with highly conductive metal cladding that is outdoor proof and suited for harsh environments, making this gasket type suitable for military, medical and all other applications were high demands are made on the EMI shielding in the magnetic low-frequency area.


Standard shapes

6580_technical_drawing

Part number 6580 : Big side clip-on gasket

6585_technical_drawing

Part number 6585 : Small clip-on gasket

6585_technical_drawing

Part number 6590 : Big clip-on gasket

6595_technical_drawing

Part number 6595 : Side clip-on gasket


Conductive flexible edge protector

The gasket is designed to slide easily over metal flanges to help reduce installation costs and is a good choice for retrofit applications.

Applications

  • Connecting plates
  • ESD (static discharge)
  • EMI shielding

Benefits

  • Easy gasket installation
  • Resistance to heat, humidity, salt fog, corrosion and rain

* The red line is an indication of the conductive layer.

 
Partnumber 6501 6502 6503 6504
Available types F, H F, H F, H F, H
Clamping range 1mm 1-2mm 1-3mm 6-8mm
Core material PCV PCV PCV PCV

 
Partnumber 6505 6506 6507 6508
Available types F, H F, H F, H F, H
Clamping range 1-4 mm 1-3mm 1-4mm 1-3mm
Core material PCV PCV PCV PCV

 
Partnumber 6509 6510 6511 6512
Available types F, H F, H F, H F, H
Clamping range 4-6mm 9-12mm 1-4mm 18-20mm
Core material PCV PCV PCV PCV

     
Partnumber 6513 6514                                                
Available types F, H F, H                                                         
Clamping range 1-2mm 1-3mm    
Core material PCV PCV    

Sealing section

This combination of materials decreases the number of gaskets needed per cabinet. This makes the sealing section a economic solution for application where an environmental seal as well as EMI shielding is needed.

Features

  • High performance solution
  • Very cost efficient solution

* The red line is an indication of the conductive layer.

 
Partnumber 6521 6522 6523 6524
Available types F, H W, F, H W, F, H W, F, H
Clamping range 1-4mm 1-4mm 1-4mm 1-2mm
Core material PCV PCV PCV PCV

 
Partnumber 6525 6526 6527 6528
Available types W, F, H W, F, H W, F, H W, F, H
Clamping range 1-4mm 1-4mm 1-4mm 1-2mm
Core material PCV PCV PCV PCV

 
Partnumber 6529 6530 6531 6532
Available types W, F, H W, F, H W, F, H W, F, H
Clamping range 1-4mm 1-4mm 2-4mm 2-4mm
Core material PCV PCV PCV PCV

 
Partnumber 6533 6534 6535 6536
Available types F, H F, H W, F, H W, F, H
Clamping range 2-4mm 2-4mm 1-4mm 1-2mm
Core material PCV PCV PCV PCV

   
Partnumber 6537 6538 6539  
Available types W, F, H W, F, H W, F, H  
Clamping range 1-3mm 1-4mm 2-4m  
Core material PCV PCV PCV  

Conductive edge protector

This is a very rigid profile, used to protect sharp edges from damaging and still preserve the electrical conductance. This type is also suitable for connecting two steel plates or for static discharge.

* The red line is an indication of the conductive layer.

 
Partnumber 6540 6541 6542 6543
Available types F, H F, H F, H F, H
Clamping range 0.5-2mm 2-5mm 1.2-1.8mm 1.2-1.8mm
Core material EPDM, 70 ± 5 shore A EPDM, 70 ± 5 shore A EPDM, 70 ± 5 shore A EPDM, 70 ± 5 shore A

       
Partnumber 6544      
Available types F, H      
Clamping range 1mm      
Core material EPDM, 60 ± 5 shore A      

Dynamic section

Simple clip-on installation for door jambs and similar needs, edge mounts, low and high deflection.

For applications where a small dynamic range is required and a clip-on mounting is preferred. Mounts simply by
pressing into position.

The gasket comes with retaining lances lo look into desired position.

* The red line is an indication of the conductive layer.

 
Partnumber 6551 6552 6553 6554
Available types W, F, H F, H F, H F, H
Clamping range 0.8-3mm 1-3mm 1-3mm 1-2mm
Core material EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore

 
Partnumber 6555 6556 6557 6558
Available types F, H F, H F, H F, H
Clamping range 1-3mm 1-3mm 1-3mm 1-3mm
Core material EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore

 
Partnumber 6559 6560 6561 6562
Available types F, H F, H W, F, H W, F, H
Clamping range 1-3mm 1-3mm 1-3mm 1-3mm
Core material EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore

 
Partnumber 6563 6564 6565 6566
Available types F, H F, H W, F, H W, F, H
Clamping range 1-4mm 1-4mm 1-3mm 0.5 - 2mm
Core material EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore

 
Partnumber 6567 6568 6569 6570
Available types F,H F,H F,H F,H
Clamping range 1-3mm 3-5mm 1-3mm 6-8mm
Core material EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore

 
Partnumber 6571 6572 6573 6574
Available types F, H F, H F, H W, F, H
Clamping range 2.5-3.5mm 1.5-3mm 2-3mm 1-3mm
Core material EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore

 
Partnumber 6575 6576 6577 6578
Available types F, H F, H F, H F, H
Clamping range 2-4mm 2-4mm 2-4mm 2-4mm
Core material EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore

 
Partnumber 6579 6581 6582 6583
Available types W, F, H W, F, H F, H F, H
Clamping range 1-3mm 1-2.5mm 1-2mm 1.5-3mm
Core material EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore

 
Partnumber 6584 6586 6587 6588
Available types W, F, H W, F, H F, H F, H
Clamping range 1-3mm 1-3.5mm 1-3mm 1 - 3mm
Core material EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore

     
Partnumber 6589 6591    
Available types F, H F, H    
Clamping range 0.5-1.5mm 0.5-2mm    
Core material EPDM, 60 ± 5 shore EPDM, 60 ± 5 shore    

 

Wilt u...

Om een prijsaanvraag binnen 24 uur te krijgen voor Clip-on afdichting alle vormen , vul het onderstaande formulier in

Please specify the partnumber from the tables
Select an option:
W : Clip-on shielding gasket with water seal
F : Fully wrapped clip-on EMI shielding gasket
H : For heavy duty applications
* Let op: De rode blokken zijn verplicht